Electrical Engineering

Star Delta Transformation: There are some networks in which resistors are neither in series nor in parallel. Such networks are star-connected or delta-connected resistors.A familiar case is a three terminal network e.g delta network or star network.It is not possible to simplify such networks by employing series or parallel technique.In order to solve them we transfer them into one another and then apply series parallel techniques. We can transfer star-connected into delta-connected resistances by keeping the two networks electrically equivalent and vice versa. By electrically equivalent   networks means    “ Resistance between any two terminals of one network is equal to the resistance between the corresponding the second network.” Delta to star transformation: Resistance between terminals A and B (Δ-connected) R AB =R AB ||(R BC +R CA ) R AB =R AB (R BC +R CA )/R AB +R BC +R CA Resistance between terminals A and B (Star-connected) R AB =R A +R B As two networks

Combinations of resistors: Resistors are arranged in one of three forms to form electrical networks according to our desired demand. 1.Series Network   2. Parallel Network  3.Star or Delta Network                                        Series Network: A network of resistors where there is only one path for current to flow is called a series resistive circuit. It means the current in a series circuit remains the same but voltage divides across the resistors. Total resistance of the circuit is more than any resistor connected in series. A series network is shown in the following figure. Total resistance  of a series connected resistors is found by the formula R t  =R 1 +R 2 +R 3 +……….+R n I = E/R t Total voltage = E E = IR 1 +IR 2 +IR 3 +……..+IR n The equivalent circuit after calculating total resistance is given by                            Parallel Network: Such a circuit in which resistors are arranged in a way that current has multiple pa

Conductance: The conductance of a material is its property which tells us with   how easily current can flow through that material. In simplest way it is defined as “Reciprocal of resistance is called conductance.” It is denoted by G and is given by                     G=1/R Unit: The unit of conductance is mho or siemen and is represented  Ʊ. Relation: As conductance is reciprocal of resistance so it is inversely proportional to the length of the conductor but directly proportional to the area. According to above statement                G  α 1/L  ........(1)                G  α A ...........(2) By combing above two relations we have              G α A/L or                   G=   σ A/L where    σ= Conductivity and is defined as Conductivity: The reciprocal of resistivity is called conductivity. It is represented by σ. Unit: The unit of conductivity is mho per meter( Ʊ/m ) or siemen per meter.   Alternatively             

Temperature: When electric current passes through a conductor the temperature of the conductor increases due to collision of electrons with other electrons and with atoms and molecules of conductor. This temperature has a great effect on the resistance of the conductor and to find this effect a term is coined called temperature coefficient of resistance.   Temperature coefficient of resistance: Temperature coefficient of resistance tells us about the effect of temperature on the resistance of a material.It is given by the following equation                                     α = (Rt-Ro)/Rot                            where   α =temperature coefficient  Rt=resistance at temperature=t in centigrade  Ro=  resistance at temperature=0 in centigrade Unit: The unit of temperature coefficient of resistance is per centigrade. Effect of temperature on the resistance of electrical materials: Electrical materials are also classified into two major types on the basis

As conductor is made up of some material that will have certain dimensions such as length and area etc that plays a part in calculating the resistance. The resistance of a conductor depends on the following parameters 1:Length of conductor 2:Cross-sectional area of conductor 3:Resistivity  4:Temperature of the conductor Now we will explain all of above four parameters one by one . Length and Area of conductor : The resistance of material is directly proportional to the length of the conductor but inversely proportional to the area of the conductor. We know that when length of a material increases its area will decrease which means path or channel through which electrons flow will decrease. Under such a condition more collision will occur resulting in increase of resistance.Mathematically,                                                                                                  RαL .......(1)                                         Rα1/A ........(2)  By combining above

Carbon Resistors: A component whose function in a circuit is to provide a specified value of resistance is called a carbon resistor. A carbon resistor is manufactured by baking a powdered carbon mixed with a binding material. This results in a small tube with a wire attached to both ends. The range of carbon resistor is from a fraction of an ohm to several million ohms. The power rating of a carbon resistor depends upon the physical size of the resistor. Power rating means the electrical by consumed by a component or converted into another form of energy by that component. In our case resistor is going to be discussed so a large resistor is able to dissipate more energy  into heat than a smaller one which means larger resistor consumes more power and that is why its power rating is high. Color coding scheme: A color code is printed on a carbon resistor which gives us information about the resistance of that resistor. In this scheme generally a carbon resistor has four bands of

Resistor: It is defined as an electrical element which is used to confine or limit electric current through it. Resistance:  The property by which a resistor opposes the flow of current is called resistance. It can also be found from ohm’s law which states that the ratio of voltage to current is called resistance.  Mathematically                                                                    V/I = R Unit : The unit of resistance is ohm on the name of George Simon Ohm who gave ohm’s law and is defined as "When one volt of potential difference causes to flow a current of one ampere through a conductor then the resistance of conductor is one ohm". It is represented by the Greek letter omega Ω. Explanation : Resistance is the property of substance or material from which a conductor is made up of.  It opposes the flow of electrons i.e current. It is said to be found when moving electrons collide with each other, atoms and molecules of substance. This collid

Well if you are going to study Electrical Engineering first you will have to study Physics which is "Mother of Electrical Engineering". In addition to this you should be good at basic mathematics too but don't worry here we will explain each and everything in detail. So let's start.           Basic Concept:                                               First of all we would try to understand what is matter because this field starts from matter. For this I would like to give you a clear and concise overview with a latest theory in this field called modern electron theory of matter. Modern Electron Theory of Matter:                              This theory describes that all matter whether solid , liquid , gas and plasma is composed of small particles called molecules and a molecule is made up of atoms.Further an atom has two parts  nucleus which is the central part of atom. Nucleus contains protons and neutrons mainly. The charge on the proton is posit